22
Jun
19543T2 Shift Cable Kitchanged to 865436A03 for Alpha 1 Gen 2 11300. Recently replaced a shift cable on a1988 350 mercruiser alpha 1 drive.
32 mm c - Area Covered by Inner Transom Plate - Flat to within 18 in.
Alpha one shift cable removal. Mercruiser Alpha One shift cable removalinstall no tool. Remove a shift cable from an Alpha One Gen 1 out drive Here is what you can do. Look up underneath the fwd part of the drive right under the bell housing see photo below for example and you will see the shift shaft shoe engaged in the upper shift shaft.
That has to be pointed straight forward to pull the whole drive off. We now have an affordable socket tool for removing the shift cable. Order 91-12037 for about 2740 only required for R MR Alpha One or Alpha Gen II drives.
Mercruiser Alpha One Shift Cable replacement steps 1. For Mercruiser 25 30 37 and 37LX Alpha One. For more videos click link.
If you need to replace the shift cable go to Replacing Your Alpha One Shift Cable and follow the removal instructions. Turn the drive to one side and remove the two screws which hold the plastic Trim Sender. On Mercruiser Alpha One Shift Cable Diagram.
Mercruiser shift cable adjustment and install help use when installing and view Mercruiser tech drawings. MercruiserMRAlpha 1 shift cable kit OEM A03 First examine the condition of the connections on the unit. You will need to replace this cable a new one PN OEM A03.
If you need to replace the shift cable go to Replacing Your Alpha One Gen II Shift Cable and follow the removal instructions. Turn the drive to one side and remove the two screws which hold the plastic Trim Sender to the side of the Gimbal Ring. Pull the sender off and tie.
Mercruiser Alpha One shift cable removalinstall no tool. -MorrillCornelius First shift Installation Shift. May 24 2016 - This video shows how to remove or install the shift cable without buying the shift cable tool.
Follow your service manual for complete instructions this onl. Remove the cable completely from the boat. Slide the cable threw the drives bell housing then slide the bellow over the cable engine end of the cable feed the cable thew the transom attached the bellow with bellow adhesive on the large end tighten the clamp then go ahead an put the squeeze clamp on the small end and put all your cable hardware back on at the engine side bolt the outdrive back on make sure it is in forward gear when the drive is removed.
Get it as soon as Wed Aug 4. FREE Shipping by Amazon. Danti for Mercruiser Alpha Gen One Two 1 2 MC MR Lower Shift Cable Replace Kit 865436A0219543A1019543A8GLM 21451Mallory 9.
Make sure this fits by entering your model number. New tool for removing and installing shift cable on Mecruiser Alpha One drives 1983-present and fits cables for RMR pre-alpha from 1978-1982. See more product details.
Mercruiser alpha one shift cable assembly kit glm part number. The remote control will pull the dash shift cable when placed into forward gear. Glm oem item 21162 11 49910 nut 21462 38473 wrapping 21712 na shift cable 32600 12 815472.
Pull on the shift cable guide to remove any slack from the cable. Remove the locknut holding the adjustment barrel in place. Remove the clevis pin with a set of pliers and disconnect the brass adjustment barrel from the post.
Adjust the barrel by rotating it until youve removed the slack. Recently replaced a shift cable on a1988 350 mercruiser alpha 1 drive. Shift interrupter works fine in foreward but shuts off the engine in reverse.
Could you advise the proper sequence to adjust. The shift control cable is a different cable. 35000 would be a fair price considering this could be a PIA for the weekend DIY.
You have to be sure that the new shift cable boot is sealed and secure or youll have a water leak into the boat and snaking the new cable thru the transom bracket and up to the mounting bracket can be another PIA. Lower Shift Cable replacement on Pre-Alpha. I just finished changing all the bellows and the water intake tube on my boat which involved removing and replacing shift cable.
It took about 4 to 5 hours and I am a true novice. The special shift cable socket tool makes removal and installation much easier. Trying to install the cable without the correct tool will damage the new cable.
19543T2 Shift Cable Kitchanged to 865436A03 for Alpha 1 Gen 2 11300. 91-12037 Alpha Cable Installation and Removal Tool3000. New lower shift cable kit for Mercruiser outdrives.
MC-I MR Alpha 1978 newer Alpha One Gen I 1983-1990 Alpha One Gen II 1991-2016 Kit contains both inner and outer cable anchors and cable ends. Cross reference MercruiserQuicksilver 865436A02 19543A10 19543A8. B - Transom Surfaces-Parallel to within 18 in.
32 mm c - Area Covered by Inner Transom Plate - Flat to within 18 in. 32 mm d - Area Covered by Gimbal Housing Assembly - Flat to within 116 in. 16 mm e - Transom Angle-10 to 16 f - Keel if Equipped - Remove 4 ft.
12 m forward of transom.