15
Jan
And yeah it seems that wheel bearings are good for 200000 km - on these cars. The cost to replace one front-wheel hub assembly varies widely.
On average the cost for a Subaru Outback Wheel Hub Assembly Replacement is 153 with 58 for parts and 95 for labor.
Cost to replace hub bearing assembly. The factory replacement part costs about 370 or a Raybestoes hub assembly costs about 220. This makes the job about 470 using OE parts or about 320 using aftermarket parts. On the rear of the vehicle axle bearings are used.
You will pay from 130 to 550 for hub assembly replacement. The labor should cost you about 70-90 while parts will run between 65 to 400. Hub Assembly Replacement Cost Comparison Your Mechanic.
Labor and Part Costs. The cost of a wheel hub assembly or bearings can start from as low as 60 and go well over a hundred dollars. The make and model of your car will determine the exact price.
Wheel hub replacement costs can vary from car to car as well as who you buy them from. On the rear costs are about 244 for a rear hub assembly replacement or 289 if done with OE parts. Labor time for wheel bearing replacement isnt necessarily charged at book rate some shops use a flat fee for common hub assembly replacements.
And parts prices vary widely as well. Wheel Hub Assembly Replacement Cost. Wheel Hub Assembly Replacement Cost.
The average cost for wheel hub assembly replacement is between 406 and 525. Labor costs are estimated between 109 and 138 while parts are priced between 296 and 387. Some model use hub bearings in the rear.
With this type the wheel bearing attaches together with the hub assembly and built in with speed sensor if the car has ABS on it. The average cost to replace this part is between 400 to 500 for one side including the labor. Hub Wheels Bearing Replacement Cost.
So there some vehicle models that use hub bearings in the rear. These types of vehicles wheel bearing as I mentioned earlier have their wheel bearing attached to the hub assembly and they have s built-in speed sensor. 435 each assembly.
Id think changing out the bearing and hub would be cheaper considering removing the knuckle costs the same in both cases and press work shouldnt add more than 50 each side. As long as the knuckle is in good condition otherwise. Answer 1 of 13.
Well it really depends on the hourly rate. Certain shops range anywhere from say 65 to 125 per hour. Corporate stores typically have very talented technicians that make less per hour but see more business than some independent shops.
I personally know a technician at an ind. No alignment is necessary when replacing Mk5 wheel bearings because the whole bearing and hub and ABS trigger wheel is one assembly that bolts to the steering knuckle. BUT there is no way that bearing assembly only costs 50 bucks.
And yeah it seems that wheel bearings are good for 200000 km - on these cars. Ive had all four corners done on. So be prepared to pay a lot more to replace multiple wheel bearings.
Rear Hub Bearing Replacement Cost. Some types of a car they are using hub bearing in rear side. The price of hub bearing bit more pricey than ordinary wheel bearings.
Why this type of this bearing more pricey. Because this bearing come assembly with ABS sensor and hub. The average price for part itself around 200 to 300 each.
As long as the aftermarket is of good quality there is no problem using aftermarket vs. The labor time guide calls for 13 hours per side to complete the job. Any price above 850 is a ripoff.
I just replaced the rear hub assembly wheel bearings on my 2005 Honda Pilot. The price for the Subaru and Honda hubs are nearly identical 110 each for MOOG so if the dealer marks them up 100 440 parts. This configuration is most common on older cars and 2WD trucks and vans.
They are the easiest to remove and replace. The bearing comes out of the hub assembly and a new one goes in its place. This repair is not labor intensive under normal circumstances and the parts are fairly inexpensive.
The cost to replace one front-wheel hub assembly varies widely. Some variables include the make and model the garages labor rate and the cost for parts. The national average is about 350 to.
PREVIOUS VIDEO httpsyoutubefZAvG0pEQVAIn this video I replace the Hub and Wheel Bearing assembly on a 2006 Jeep Commander. Both front wheel bearings. The average cost for a Wheel Hub Assembly Replacement is between 365 and 400 but can vary from car to car.
So ok you wanna replace your front hubs cuz your bearings are whininggrindinghumming whatever I recommend not buy cheap parts. Cost me 300 for two. Make sure you order the right ones front and back are different.
Ok so block your rear tires. Jack up the front. Replace front wheel bearings only or entire hub assembly.
If this is your first visit be sure to check out the FAQ by clicking the link above. You may have to register before you can post. Click the register link above to proceed.
How much does Wheel Hub Assembly Replacement cost in Harbor City CA. Get an estimate instantly. Service parts cost recommendations from YourMechanic.
Your definitive guide to Wheel Hub Assembly Replacement in Harbor City CA. Wheel bearing replacement cost also depends on the hub assembly as the non-serviceable hub assembly can cause up to 400 to 800. Prices can go much higher in non-serviceable hub assembly with bearing press.
The car makes model and year can play a significant role in the price of wheel bearing replacement. How much does a Wheel Hub Assembly Replacement cost. On average the cost for a Subaru Outback Wheel Hub Assembly Replacement is 153 with 58 for parts and 95 for labor.
Prices may vary depending on your location. Yeh I just replace the entire Knuckle assembly like you and other associated parts while Im in there. I do all OEM and get new bushings all the way around that way.
With a 200 HubBearing and a 300 Knuckle and the other parts it ends up being a little pricey for just a noisy bearing but my 11 OB has 180k and the bushings are shot.