Evinrude lower unit oil change

If outboard oil is not available use Type lM SAE 30 Automotive Motor Oil. Carefully remove vent hose from the oil reservoir upper fitting.

G2 Lower Unit Oil Change Procedure Oil Capacity.

Evinrude lower unit oil change. This video show how to change the lower unit oil AKA. Lower unit gear lube on a 25 hp Evinrude E-TEC outboard boat motor. This takes minimal tools and cos.

Time to change the oil in the lower unit of my Evinrude 30 horsepower outboard motor. The last time the oil was changed was probably 6 or 7 years ago when the water pump was changed and a new powerhead was installed. While my wife and I were in Jasper Texas taking care of some business we stopped by the Evinrude dealership and got some gear oil.

Changing the Lower Unit Oil The lower drainfill plug screw is usually located on the starboard side of the lower unit beneath the bullet-shaped portion of the lower unit housing. Locate your drainfill plug screw and adjust the trimtilt of your outboard motor or sterndrive so that this plug is in the lowest position possible in order to drain the used oil thoroughly. 72 Evinrude 65HP– how to change oil in lower unit.

Let it set for a day or two without runnin it when you pull out the lower plug if water doesnt come out you probably dont have a leak. You dont have to pressure check it every time you change it. You put the oil in the bottom hole until it runs out the top so you dont get any air pockets.

G2 Lower Unit Oil Change Procedure Oil Capacity. Gearcase only 389 fl. 1180 ml Gearcase vent hose and oil reservoir 456 fl.

1350 ml The drain plug is behind the front water inlet screens. Carefully remove vent hose from the oil reservoir upper fitting. Remove the low water intake screens.

Rremove the lubricant drainfill plug. Make sure that the engine is in a full verticle position so the old oil drains outremove the lower drain screw then the top onelet drain for awhile. Refill from the bottom drain pushing the oil in and air out till oil comes out the top hole.

Replace the top drain screw then remove the oil container and replace the lower plug. I want to change my 2014 Evinrude Etec 115 horses lower unit oil this weekend. I used to own a 2000 Mercury 150 horse and I used the Mercury brand Quicksilver lower unit oil which I still have a bunch ofCan I use the Quicksilver lower unit oil in the Evinrude or should I use only Evinrude brand.

Gearcase only 389 fl. 1180 ml Gearcase vent hose and oil reservoir 456 fl. 1350 ml Carefully remove vent hose from the reservoir.

Remove the low water intake screens. Remove the lubricant drainfill plug. From the gearcase into a suitable container.

How to change the oil in your boat engine. With other outboards they require you to have a break in period dealer scheduled maintenance and oil changesWith an E-TEC G2 you have no break in period 5 years or 500 hours dealer scheduled maintenance and no oil changes. Ive only sold a few G2s and havent found one below the min mark.

Oil level will change some with temperature. It is worth watching but that gearcase is like any of the older ones if the oil is above the top of the gearcase then it is full. Joined Jul 13 2009.

8 Jul 24 2009. 98 black means you need to change it more often - grey is water mixing with the oil but 2 does not seem too horrible. Make sure the seals on the filloverfill screws are intact and there is no fishing line on prop shaft.

Slip a basin under the bottom of the motor to catch the oil as it drains from the lower unit. Loosen the drainfill plug on the bottom of the lower unit with a screwdriver and remove the plug. Rub the magnetized end of the plug between your thumb and forefinger feeling for bits of metal.

Changing your oil is a type of preventative maintenance that will help keep your outboard lower unit in prime shape so long as you keep up with it. At the bare minimum you should change the oil out at least once a year and that can be enough. You simply remove the lower drain screw place an oil pan under the gearcase remove the vent screw and let the old oil fully drain.

Note the colour of the oil that exits first. If it is milky white let us know. That indicates water intrusion and will need to be addressed.

At 415 hrs I changed the lower unit oil and it had a milky appearance. I changed it again after 25 hours when it got to 440 and although it wasnt as bad it was still milky. I brought it to the dealer and the pressure test revealed no leaks.

Heres the questionI was told it wasnt needed to replace the plastic o-ring on the lower unit screws. Johnson Evinrude XD 30 2-Cycle Oil XD30 FOR USE IN CARBURETED 2-CYCLE OUTBOARDS. XD30 is formulated for water-cooled 2-cycle outboards and other 2-cycle engines that specify TC-W3.

Brown lower unit oil is a sign of rust and is usually found in a gear case that has been sitting for awhile. For example in a boat that is put in storage and left for a season or a year or two. If there was any water in the lower unit when it went into storage then the water and gear oil.

If outboard oil is not available use Type lM SAE 30 Automotive Motor Oil. Use double the recommended amount of oil in 1hi mixture with a new motor or after overhaul. Mix oil and gaso-line thoroughly using a separate container before pouring mixture into fuel tank.

The lower unit gears and bearings are. Changing Yamaha F225 Gearcase Lube. Tilt the outboard to about 30-degrees which puts the lower unit at an optimum angle draining the oil.

Remove the oil vent screw and washer from the top right side of the lower unit. Next inspect the washer for wear and replace it if necessary.