21
Apr
Water in lower unit oil - 1981 E15RCIS 15hp Evinrude. The process shown in this video is almost identical of all Johnson Evinrude OMC lower units pre-1982 under 25 hp 5 55 6 95 10 15 18 20 25 hp motors.
This is compatible with 4 Cylinder 75-115 HP models from 1995-2006 and 6 Cylinder 135-175 HP models from 1991-2006.
Evinrude lower unit seal replacement. You can however replace the two lower unit seals in your Evinrudes lower unit while it is still attached to the rest of the motor by sliding the bearing carrier off the propeller shaft leaving the propeller shaft in the lower unit. When putting the lower unit back together one of the ball bearings jumped off the table and into the grass. I tried to find it.
I have ordered more. Johnson Evinrude Lower Unit Seal Kits. If you have owned an outboard motor for any length of time you have probobly had issues with the lower unit sometimes called the gearcase.
Of of the most common issues with outboard lower units are leaky seals that allow water to get into the lower unit oil and degrade the effectiveness lubrication. Lower Unit Seal Replacement for Evinrude 225. March 2012 in Southeast General Fishing The Outdoors 1.
I must say I am impressed with the recent purchase of a used 96 E225. However after running it at the dock Friday morning checking the control linkages I began to notice an oil sheen on the water. Theres something puzzling me about replacing the lower unit seals first of all the drive shaft stupid design which is an upper shaft fits into a lower shaft with a big wobble in the upper shaft is stretching the upper seals way too much and causing them to leak when air pressured according to service manual procedure even when the seals are brand new.
Secondly the service manual says to put. Water in lower unit 60 hp johnson. 18 HP Prop Shaft seal.
Water in lower unit oil - 1981 E15RCIS 15hp Evinrude. 1998 200 hp Venom with water in lower unit. 78 rows Detailed diagrams allowed me to find the exact parts I needed to repair an Evinrude lower.
Oct 18 2011. 70HP lower unit seal replace. Shouldnt be to hard you can buy a seal remover its been awhile but 15 or so or if your careful you can use a screw driver use it as a pry bar between the rubber of the seal and prop shaft push down a little at a time and work it around the inside of the seal.
Sierra 18-2656 Lower Unit Seal Kit for Johnson Evinrude 99 15HP Sierra replacement engine parts are designed to meet OEM specifications. 1 18-2025 Oil Seal 2 18-2028 Oil Seal 2 18-2029 Oil Seal 2 18-4248 DrainFill. 30 rows Gearcase Seal Kits.
Sealing the gear oil inside the gearcase and keeping water from. Changing a Johnson Lower Unit Seal. The lower level of a Johnson outboard houses the water pump and propeller among other important parts.
Two seals keep the water out of the gears and keeps packed grease in so if the seals become damaged in any way this can cause lots of problems. Therefore when a seal is damaged it must be replaced. The process shown in this video is almost identical of all Johnson Evinrude OMC lower units pre-1982 under 25 hp 5 55 6 95 10 15 18 20 25 hp motors.
Lower Unit Shim Kit. List price 1530 replaces OEM 323362 323361 314745. List price 1260 replaces OEM 436745.
List price 1065 replaces OEM 431708. NOT PICTURED IN DIAGRAM. List price 6495 replaces OEM 5001594.
List price 6395 replaces OEM 5000411. Removal Replacement of the Shaft Seals Without Disassembling the Lower Unit. This section deals with either the driveshaft seal below the water pump OR the prop shaft seals which consist of 2 back to back seals of the same size.
This back to back method uses one to. I have a few motors with water getting into the lower units. 1954 10 hp1956 10 hp and a 1957 18 hp.
Both 10s are Johnsons and the 18 is a Evinrude. I think I can remove the drivesfat and propshaft seals without a special tool but being as I have to do 3 lower units the tool to do the shift shaft looks like I should have that one providing. Approximate cost for lower unit seal replacement To find the leak drain the gearcase and use either the vent or drain hole to apply air pressure to around 12 PSI.
If you dont hear the air leaking drop the unit in the water so you can see the the air bubbles. New Red Rhino JohnsonEvinrude 40-60 HP 2-CYL Gearcase Seal Kit 1978-1988 Replaces OEM 396355 This listing is for a New Aftermarket JohnsonEvinrude 40-60 HP 2-Cylinder Gearcase Seal Kit which will fit models from 1978 to 1988. This item will replace OEM No.
Lower Unit Seal Kit for all Johnson Evinrude V4 V6 V8 lower units after 1973 Replaces JohnsonEvinrude part s. 5000411 5006373 Mallory 9-74106. Rebuilding or Resealing a Johnson Evinrude 6 or 95 Hp Lower Unit Gearcase.
I found myself in possession of a 1979 Evinrude 6 Hp outboard that needed its lower unit some people call it the foot rebuilt with a new seal kit. I created a couple of videos. Welcome to The Lower Unit Store supplier of thousands of new and used quality lower unit parts.
We specialize in Johnson and Evinrude lower units but do have Mercury Yamaha and Honda lower units occasionally. We also stock both upper and lower OMC Cobra outdrives and all the gears shafts seals. Replacement unit for Johnson Evinrude Magnum and Magnum 2 lower units.
It is a direct replacement for the Mag II If you are replacing a Mag the original you will need to remove the alignment pins from the new lower unit. They are only offered in Black. Does not come with upper drive shaft shift.
New Red Rhino JohnsonEvinrude 60 and Ficht Lower Seal Housing Replaces OEM 340559 This listing is for a New Aftermarket JohnsonEvinrude 60 and Ficht Lower Seal Housing. This is compatible with 4 Cylinder 75-115 HP models from 1995-2006 and 6 Cylinder 135-175 HP models from 1991-2006. That encluded replacing all seals the Impeler and winterizing.
The labor cost was 21000the balance parts and taxI belive the seal kit was 5795 and the impeller kit 3595. Pressure test it and see what seal is leaking. On a 15 it might be real easy to do the outer seal because I.