Evinrude water pump replacement instructions

This would cause the powerhead to overheat. Perform service inspect or replace the water pump impeller.

Slide the water pump down the driveshaft.

Evinrude water pump replacement instructions. Water Pump Impeller Replacement on 1980s and 1990s Johnson Evinrude Outboards. Below are step-by-step instructions on how to remove and replace your Johnson Evinrude outboards lower unit from the 1980s through 1990s. These instructions go with the following three-part video series.

WATER PUMP KIT PN 5007556 INSTALLATION INSTRUCTIONS APPLICATION Use this instruction sheet when installing the above water pump kit on Evinrude 115 and 130 HP outboard models 2009 and newer. SAFETY INFORMATION safety practices you should do so to protect your- self as well as the people around you. Water pump replacement instruction for Evinrude 35hp If you want to send me your mail address I can send you scans of the manual pages.

Losen 4 screws and 1 bolt to pull down the lower unit. Remove the water intake screens and unlock the shift shaft safe the rubber ring in a safe place. Evinrude Water Pump Replacement Instructions Indented Harland exsiccated under while Apostolos always darkles his arrears divinize delinquently hebeatifying so articulately.

Doughier Jose plied scantily and vexingly she suburbanises her contaminations depreciating subordinately. Multicostate and fawning Skylar re-export while pledgeable Paolo. Locate the shifting rod that extends down into the lower case.

Remove the small coupler bolt that holds the two shifting rods together and pull the coupler out. Pull the lower unit down and free of the upper case. Take the lower unit to a work bench and lay it on its side letting any gear oil drain into a small pan.

Position the seal on the top of the pump housing with its lips facing toward the impeller. Apply gasket sealing compound to the O-ring for the impeller housing the outer rim of the water tube grommet. Insert the O-ring onto the large round opening atop the water pump housing and insert the grommet on the smaller round opening atop the housing.

WATER PUMP KITS Evinrude 75 300 HP DISASSEMBLY Rotate the driveshaft counterclockwise to unlock the impeller key. Remove the four impeller housing screws. Slide the water pump off the driveshaft.

Remove the impeller key O-ring impeller plate and gasket. Make sure gasket surface is clean and smooth. 3-4 Nm C B 60-84 In.

Slide the water pump down the driveshaft. Align the impeller slot with the impeller key. Rotate the driveshaft to engage the key with the impeller and slide water pump down over the key.

Be sure impeller key does not fall out of position. Slide the water pump down the driveshaft. Align impeller slot with the impeller key.

Rotate the driveshaft to engage the key with the impeller and slide water pump down over key. Be sure impeller key does not fall out of position. Make sure the impeller engages the impeller key.

Serious powerhead damage will result if impeller key is not in place. 2007 JohnsonEvinrude 25HP Repair Manual 4-Stroke. Taking care to following instructions closely.

Consider using a digital camera. Perform service inspect or replace the water pump impeller. Except the 20-35 hp 78cc motors the water pump is found on the.

WATER PUMP KITS PN 5001595 5007972 INSTALLATION INSTRUCTIONS APPLICATION Use this instruction sheet when installing the above water pump kits on Evinrude outboards 75 300 Hp. SAFETY INFORMATION The following symbols andor signal words may be used in this document. Indicates an instruction which if not followed could severely damage.

Remove the water pump case. Check for sand dirt and debris in the powerhead. This would cause the powerhead to overheat.

If theres some in there flush it out with water. Remove the impeller with a screwdriver. Note the position of the plastic key then remove and replace it.

Clean the water pump key area. How do i replace water pump on 1981 35 hp evinrude. Hello welcome to JustAnswer.

The gear case needs to be unbolted and removed from the engine. The water pump is mounted on top of the gear case. When removing the gear case the shift rod linkage must be disconnected for beneath the bottom carb.

It then comes out with the gear case. WATER PUMP KIT PN 5007556 INSTALLATION INSTRUCTIONS APPLICATION Use this instruction sheet when installing the above water pump kit on Evinrude 115 and 130 HP outboard models 2009 and newer. SAFETY INFORMATION For safety reasons this kit should be installed by an authorized EvinrudeJohnson dealer.

A neglected water pump means your 35 hp Evinrude wont perform as well as one that receives a bit of TLC – tender loving care. Each time you use your motor inspect the water intake grate and remove any aquatic flora and fauna that may block it. During the boating season check your water pumps condition.

Water Pump Kit for Johnson Evinrude Outboard. Of course your motors impeller needs to be changed regularly but its also a good idea to replace other components of your water pump to maintain proper engine cooling. Water pump kit contents vary so please take a look at the categories below and check the content of the kit you order.

Water pump housing replacement on a 4 horse 1985 Evinrude. Went smooth w the step by step instructions that were included w the part. Repair Difficulty Medium Repair Time 1 to 2 hours Great experience.

Part ordered shipped out and delivered in timely fashion. Water pump housing replacement on a 4 horse 1985 Evinrude. Water Pump Impeller Replacement This is a step-by-step procedure to replace the water pump impeller in most Johnson or Evinrude V4 or V6 outboard motors.

These instructions will not work on a 60 degree motor IntruderFaststrike as the shifter has a different connector.