Hot water heater element won t come out

If its tripped then theres no power going to the electric water heater. It should be about 12 ohms.

This is a common problem and can be diagnosed by dismantling your boiler and using a multimeter to check the resistance of the element.

Hot water heater element won t come out. Cant remove heating element from water heater. Hj AZ If you really want to do it rather than replace the water heater. Drill out the two holes where the wires attach to the element.

Then insert two good screwdrivers or punches. Place a bar or lever between them and twist it out. You can try loosening the stuck heater element from the part.

It may happen if the element has not been stuck for an extended period. However it would be best to use the proper set of tools and correct sensitivity. If you rush too much you may end up damaging other parts of the device.

One year old is rare you must have very hard water the reason it will not come out is because it has build up on the element GARY C. You will just have to try and twist and pull it out worse case senerio you will need to saw the part of the element rod that you could get out and insert a new one leaving the severed old one in the bottom of tank. The element wrench barely grabs the top of the element and then only spins after trying to loosen the element.

Becasue the element wrench wasnt working I knocked the plastic off the head of the element drilled 2 holes big enough to insert the end of one of my open end wrenches grabbed a significant bar for leverage to insert into the other end of the wrench AND STILL CANT LOOSEN THE bleeping element. Quite often the reason you wont be able to get any hot water is because of a broken hot water heater element. This is a common problem and can be diagnosed by dismantling your boiler and using a multimeter to check the resistance of the element.

Heating elements can break over time because they continuously heat up and cool down. If you continue to have trouble try adding a little bit of penetrating oil and then waiting maybe half an hour or heat that area of the water heater with a torch in order to use thermal expansion to your advantage. Share Improve this answer answered Aug 19 13 at.

127 satisfied customers. I had my electrican replace 2 hot water heater elements one. I had my electrican replace 2 hot water heater elements one he got out the other he said too corroded and threads stripped for it to come out he says too much sediment I said flush out.

Be sure the water heaters solidly held and wont tip. Once you crack it loose youll be fine. If you have hard or semihard water be sure to get a low watt density element.

Larry Weingarten Member Posts. 2232 March 2004 trick One more trick is to take your six point socket and grind the working end of it flat. How to Know if a Hot Water Heater Element Needs to Be Replaced.

Water Heaters - YouTube. Go to the electric panel box to see if the water heaters circuit breaker has tripped. If its tripped then theres no power going to the electric water heater.

To reset the circuit push the breaker to the off position and then to the on position. Now your water heater. Turn off the power to the heater disconnect at least one of the element wires and then check the resistance.

It should be about 12 ohms. Most fail open or infinite resistance. Dkenny 10 years ago one thing that has not been suggested.

I have replaced both thermostats and elements in a Reliance water heater which checks out 120v at each screw in thermostats and each side of elements still will not heat. Water heater still wont heat after replacing thermostat and elements. Active 2 years 8 months ago.

Viewed 16k times 0 I have replaced both thermostats and elements in. If you turn on the hot water at a faucet and nothing comes out this is an indication the supply valve was never reopened after draining the tank. Step 2 Remove the metal plate on the front of your hot water heater if its gas operated and look through the glass panel to see if the pilot light is on.

If it is youll see a small blue flame. Burner or pilot failure. For a gas-powered heater a burner unit below the tank contains the gas jets that ignite to transfer heat to the water in the tank.

If the burner becomes dirty or corroded it will struggle to draw oxygen to ignite and eventually the jets wont come on. If you have an electric water heater the heating elements inside the tank can break and lead to a loss of hot water. Sometimes your water will slowly start to cool down and this could be because the element has burned out.

If the second element fails youll be left with only cold water. When the temperature sensors or thermostats of the device dont work correctly the heating process stops or not starting at all. This makes water come out of the tapsink cold.

Check the sensors or thermostats if you can by opening the heater. Otherwise contact a professional to check them out for you as the elements may need replacement. A water heater that produces no hot water may not be getting power or it may have a tripped limit switch or one or more failed heating elements.

First check the water heaters circuit breaker in the service panel to make sure it hasnt tripped. If the breaker has tripped switch it off then switch it back on again. The top element controls the bottom element and if it goes bad your unit wont be able to generate hot water.

What causes a heating element to burn out in a water heater. The most common cause of burned out elements on new water heater installations or new element replacements is. If you have a water-based heater your problem might be with one of the thermostats.

Your heater has two cylinder thermostats located differently depending on the manufacturer. Be sure to check both of the thermostats since malfunction of even one could make an issue such as lukewarm water flowing from the hot water tap.