31
May
Using a brass drift punch carefully tap around the small diameter end of the cup to drive out. It is recommended to use a set of dial calipers to obtain these measurements.
How to change trailer hubs - YouTube.
How to change a trailer hub. How to change trailer hubs - YouTube. Simple way to change hubs on a trailer. Simple way to change hubs on a trailer.
About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy Safety How YouTube works Test new features Press Copyright Contact us Creators. Take 1 wheel off the trailer to access the hub assembly. Loosen the nuts on all wheels with a lug wrench while the trailer is on the ground.
Jack the trailer up just enough to lift the wheels off the ground. Finish unscrewing the nuts on 1 wheel with the lug wrench remove them and slide the wheel off the hub. To determine if there are compatible hubs and associated bearings to replace your current hubs to a more standard size you will have to take several precise measurements on the spindle of your axle.
It is recommended to use a set of dial calipers to obtain these measurements. The item you selected Trailer Hub Assembly part 8-258-5UC1 is a replacement hub which uses Inner and Outer Bearing L44649. The bearing numbers will be stamped or lasered onto the flat back side of the bearings.
The other things you will need to determine are the bolt pattern the size of your trailer wheel and the axle capacity. Mobile home axle hubs can be converted by changing the axle hub and adding a wheel adapter. In the past mobile home axle hubs were frequently adapted and repurposed for trailers and even trucks.
Today however many of these uses are prohibited by law in various states. In fact many manufacturers stamp. This video illustrates how to figure out the size of your trailer hub so you can get the appropriate sized replacement.
Remember that the rear seal must face outwards from the hub towards the suspension unit. Grease the inside of the hub and insert the front bearing with the tapered edge facing in. Slide the hub onto the shaft.
Remember that the wheel nuts face out. Grease the front bearing again now it is in the hub and place a large washer on top of it. Replacement Hub Assembly Needed for 4800 lb 1992 Ranger Trail Tandem Axle Trailer Recommended Trailer Hubs for 2200 Pound Axle with L44649 Bearings and 5 on 4-12 Bolt Pattern Will the 2K Timbren Axle-Less System A20RS545 Work with 15 Inch wheels.
The first thing you will need to know is the bolt pattern of your hubs. This is so you get a hub that is compatible with your wheels. I attached an FAQ article on determining bolt pattern for you to check out.
Next thing you will need to know is what spindle you have on your trailer. Changing Rim Sizes on my Boat Trailer from 14 to 15 What is the Actual Load Capacity of Kenda 21560-8 Trailer Tire8-Inch Wheel AM3H325. Trailer and Wheel for Size 185x85-8 with 5 Lug Bolt Pattern.
Speed Rating of Special Trailer Tires in Size ST21560-8. How To Determine Correct Lug Nuts for a Trailer Hub. Reinstall the tire and wheel onto the trailer tightening the lug nuts to the manufacturers specifications.
Remove the jack stands and lower the trailer to the ground. Move to the other side of the trailer and repeat the process to replace the opposite hub. Or you can follow the link I attached that will take you to the page that has all of our replacement hubs.
You would want to first select the bolt pattern that you have next select the inner bearing you have followed by selecting your outer bearing and then all the correct hubs will be listed. Place the hub on a flat work surface with the cup to be replaced on the bottom side. Using a brass drift punch carefully tap around the small diameter end of the cup to drive out.
After cleaning the hub bore area replace the cup by tapping in with the brass drift. Grease Cap for a Harbor Freight Trailer with 2037 Inch - 2042 Inch Hub Bore. Recommended Grease Cap for a 2008 Triton Sea-Doo Trailer with 203 Inch Hub Bore.
Bearing Buddy Grease Caps for Hub Bore Dimension of 205-Inches. Availability of Replacement 182 Inch Dust Cap for Older Trailer Hubs. Changing the hubs means not only hubs but new wheels tires and air.
I have found a source of 145 trailer tires not mobile home and have plans to remove existing tires wire wheel or sand blast the old rims paint them up and install new tires. To pre-load the bearings install the spindle washer and spindle nut onto the spindle with the hub and bearings in place. Tighten the spindle nut finger tight until snug and then with channel-lock pliers or a crescent wrench tighten the spindle nut another 14 turn or about 15 to 20 ft pounds of torque.
Now turn the hub ten revolutions.