How to change oil in tohatsu outboard

Run the outboard for a minute before changing the oil to warm the used oil which makes it less viscous and helps it. Well I had just done that.

For the longer answer read on.

How to change oil in tohatsu outboard. In this video I go over how to change the motor oil on a 4-6hp TohatsuNissanMercury outboardSHOP10W30 outboard motor oil Mercury OEM oil. How to replace the lower end gearbox oil in a Tohatsu M50D2 2 stroke outboard- - - - - - - - - - - -Due to factors beyond the control of FixItSam it cannot. Lower unit marine oil pump.

Httpsamznto2UAlqrHIn this video I show you guys how to change the gear oil on a To. Into the BOTTOM drain hole. Then slowly squeeze the bottle to force the oil into the lower unit.

Continue adding oil until the lubricant is flowing freely from the top hole and is free from air bubbles. Keep the bottletube in the bottom plug or plug the hole with your finger and re-install the TOP plug. 40 rows into the BOTTOM drain hole.

Then slowly squeeze the bottle to force the oil into the. The manuals are in Adobes PDF format. In order to downloadview the manuals you must have the Adobe Acrobat Reader installed on your computer.

Click here to download the FREE Acrobat Reader program NOTE. If you have trouble viewing the PDF file in your browser try right-clicking on the link then choose the option to Save As and save the. Well the blinking oil light means it has been a 100 hours and it is time to change the oil.

Well I had just done that. So I contacted Tohatsu and they have a way to turn the light off by turning your key on without starting the motor and then pull the kill switch 5 times every 10 seconds and it is supposed to reset. Add fluid to the hydraulic reservoir until its even with the bottom of the fill spout.

Step 2 Use the trim control to move the motor into the up position then into the down position several times to burp the hydraulic system. From giving you access to online owners manuals and step-by-step instructions for changing your lower unit oil to helping you calculate the right gas-to-oil mixture ratio and answering your questions about Tohatsus TLDI series 2-stroke engine the links below offer helpful online resources to help you keep your Tohatsu outboard motors running smoothly. With the exception of our outboards which have oil injection systems Tohatsu 2-stroke outboards require a 501 20mL of oil for each liter of gas oilgas mixture after the initial break-in period.

Tohatsu outboards which have oil injection will automatically mix the correct amount of oil and gas depending on the engine requirements. You dont have to pre-mix your oil gas with these. Welcome to the step-by-step guide to changing your outboards lower unit oil.

This 8-step process is all it takes to ensure the oil in your lower unit is properly maintained. The chart at the end of this guide lists the approximate amount of oil needed to fill the lower unit of each model currently offered by Tohatsu. Half-way to 34 on the dipstick is fine.

Run Non-synthetic 10w-30 FC-W oil. If you are in a really hot climate 10w-40 is OK. Change the LU lube at the same time.

Also a good time to inspectre-gapchange the spark plug. The specs are in the owners manual. Suck some out put your finger on the end you are sucking on and put the oil end in a container and blow the oil out.

The engine doesnt hold much so you could change the oil this way. At boat yards where they dont want oil spillage they use a suction pump and you could also go that way. Good luck Sum Our Endeavour 37.

The body of the Tohatsu engine is protected by several layers of special coatings after which four layers of paint and a layer of special varnish are applied. Tohatsu Corporation offers outboard engines ranging from 25 to 140 horsepower. For our country the fact that Tohatsu motors are undemanding to the quality of fuel and oils is important.

For your 4-stroke outboard you should use Genuine Tohatsu FC-W 4-Stroke Oil. Tohatsu 4-Stroke Oil has been specially formulated to handle the higher RPMs that outboards are subjected to as well as special rust inhibitors to combat the harsh operating conditions of the marine environment. Genuine Tohatsu Oil reduces frictionwear and ensures the internal components.

YOUR TOHATSU OUTBOARD MOTOR OWNER REGISTRATION AND IDENTIFICATION Upon purchasing this product be sure that the WARRANTY CARD is correctly and. Oil Plug Lower Stop Switch a s d f g h j k Choke Knob Fuel Connector Primer Bulb Fuel Tank Fuel Tank Cap Air Vent Screw Fuel Connector Fuel Pick up Elbow 6B MF 8B MF 98B MF. NAMES OF PARTS 12 2.

How to Change an Outboards Engine Oil. After buying the oil and a new oil filter get a wrench or flathead screwdriver some shop towels or rags and a drain pan. Run the outboard for a minute before changing the oil to warm the used oil which makes it less viscous and helps it.

The short answer is yesgo ahead and use the new Mercury oil. For the longer answer read on. Make sure your outboard is filled with an FC-W marine oil that matches the viscosity and spec listed in the owners manual.

There is a section in your owners manual that shows you how to change the oil complete with pictures etc and a section which describes how often etc. Welcome to the step-by-step guide to changing your outboards lower unit oil. This 8-step process is all it takes to ensure the oil in your lower unit is properly maintained.

The chart at the end of this guide lists the approximate amount of oil needed to fill the lower unit of each model currently offered by Tohatsu. I have a small puzzle. I need to replace oil filter in my Tohatsu.

Dealer says to go with original ones. Sure no problem the thing is they are not available in Canada What replacements would you guys recommend.