22
Apr
Below are the instructions depending on whether youre on mains power or gas at the time. Both electric and gas water heaters use the same anode rodsAnd you can find sacrificial anode rods in various lengths.
In this video This Old House plumbing and heating contractor Richard Trethewey explains how to change a water heater anode rod.
How to change the anode in a hot water heater. You have a higher than usual water bill. How do you change an anode rod in a hot water heater. You will need a replacement sacrificial anode a bucket impact socket.
Make sure you have these materials ready. Turn off the power supply to your water heater. Then turn off the cold water supply which is located on the side or top of the unit.
How to Replace the Anode Rod in your Hot Water Heater. If playback doesnt begin shortly try restarting your device. Videos you watch may be added to the TVs watch history and influence TV.
Step 4 Locate and Remove. Consult your devices user manual to locate the anode rod. Its almost always accessible from the top side of the water heater where it is screwed into the device.
Most of the time you can simply unscrew the anode rod with a socket with a breaker bar or a wrench. A quick video showing how to replace the sacrificial anode rod inside a typical hot water heating tank. This procedure is essentially the same for most if n.
How often should I change a water heater anode rod. In most cases you will need to change your water heater anode rod approximately once every 6 years so long as it operates under normal working conditions. However depending on the composition of your water you may need to change the anode rod more frequently.
Click to see full answer. To replace your water heater anode rod turn off the powergas supply close the cold water valve and drain about 2 gallons of water from the tank. Use a 1 116 socket wrench to loosen the anode rod hex head.
Pull it out and replace it with the new one. Open the water and turn on the powergas. Water heater anode rods cost 50 or even less.
Anode rods generally can last about three to five years but it really depends mostly on the quality of your water and how much water travels through your water heater. By checking the condition of your anode rod every 3 years you can reduce the chances of a leak improve the quality of your water reduce water heater wear and tear and save a. In this video This Old House plumbing and heating contractor Richard Trethewey explains how to change a water heater anode rod.
1 Turn off water and fuel supply gas or electricity to water heater. 2 Partially drain the water heater. 3 Locate the anode rod on the water heater.
If necessary unscrew and lift off the cover from the top of the heater. Drain the water heater. Turn off the cold water supply to the water heater.
Attach a garden hose to the drain valve located at the bottom of the unit and run the garden hose outside. Open a hot water faucet in the house or flip the relief valve open on the water heater. The anode rod or sacrificial rod is a metal component inside your hot water heater whose purpose is to corrode before the walls of your hot water heater do hence the name sacrificial rod.
It is recommended that you replace this rod once it has corroded away. Turn off the power to your hot water tank. Open up a faucet in your home.
Attach a hose to the drain valve on your hot water tank. Turn off the cold water for the hot water tank. Drain some of the water from your hot water tank.
Locate the anode rod on your hot water tank. Click to see full answer. Hereof how often should I change the anode rod in.
A new versus an old water heater anode rod. The comparison of before and after water heater anode replacement. Go you for researching how to replace your water heater anode rod.
Maintenance on a water heater is one of those items that in. The first step is to switch off the power to your Hot Water Heater well and truly before youre ready to change the Anode. You need to give the water time to cool down so that you dont burn yourself when you remove it.
Below are the instructions depending on whether youre on mains power or gas at the time. Switch off the supply to the Hot Water System and unplug the 240 volt power. Checking and changing your anode rod is a great way to extend the life of your water heater and avoid having to replace your hot water tank prematurely.
What Type Of Anode Rod Do You Need. Both electric and gas water heaters use the same anode rodsAnd you can find sacrificial anode rods in various lengths. When in doubt purchase a longer anode rod it can always be cut down later to the.
Some experts suggest that if the anode is really difficult to remove and the heater several years old not to bother replacing the anode. While you can request an inspection as opposed to a replacement of the anode the service call labor price will be about the same for an inspection as for a replacement.