How to cut and splice rope lights

Be sure to make a smooth and clean vertical cut. Inster this tool at B and exit at C.

Drive a finishing nail into each power wire in both ends to enlarge the holes leaving about half the nails sticking out.

How to cut and splice rope lights. Once you have made your cuts use the kit to connect the lights together. It is common to splice rope lights together to make them long enough for the lighting needs. Another reason is to create a dramatic effect with different colored tubing.

Before you attempt to cut or splice LED rope lighting you need to know what you are doing to keep from ruining the lights. Cutting in the wrong spot or splicing the wrong lighting. Cut the rope light as prescribed making sure the cuts are nice and straight.

Drive a finishing nail into each power wire in both ends to enlarge the holes leaving about half the nails sticking out. Cut off the ends of both nails in one of the rope light sections. Slide a piece of shrink tube over each piece of rope light.

This is the only place that LED or incandescent rope light should be cut. When installing rope light for custom projects you may need to use connectors to join two pieces of rope light together. Remember that the two pieces of rope light being connected must be the same in voltage and wire count.

The actual cut well and then cut off the extra copper cable from the finish by twisting the light to show it. As soon as it is correctly prepared you have to add the particular connector package or splice another shade or size to the mild. Scrape the plastic cover off the end of the LED strip.

Use a sharp knife or box cutter. Cut into the plastic right above the copper dots at the end of the LED. Remove enough plastic to expose the copper dots then scrape the blade along them to clear off any plastic.

1 Cut the rope light squarely using a tube cutter or a sharp utility knife on the marks specified. Use the scissor marks imprinted on your rope light to determine where it is safe to cut. 2 Bend the end of the Rope Light 2fl from end sharply to the side which will cause one of the two wires to protrude from the cut.

Rope light spools can be cut using either sharp scissors or a knife. To cut rope light measure the area where you plan to install the rope light and then cut the tube at the nearest cutting mark. The mark that indicates a safe spot for cutting rope light will typically look like a small pair of scissors or a dashed line.

Rope to Splice Standard Tapered 20 FULL FID LENGTH. Cut and remove these strands back to the bitter end. Step 6 Re-tape the bitter end and attach it to your splicing tool.

Inster this tool at B and exit at C. Pull through until A and B line up. Remove the tool and the tape wrap from the exposed tail.

If you dont mind violating the listing of the assembly and the code. Solder them together and use shrink tubing to cover the splice make sure you put the shrink tube on one side before you solder the splice It may not be pretty but if it is well insulated it will be as safe as the plugs and probably more waterproof. A good rule of thumb is that most rope lights lights that are labeled as patio lights and Christmas lights are usually safe to be used outdoors because theyre made with durable materials.

Some Christmas lights are only for indoor use so even under these labels its. Open up the plastic flanges of the power connector and line up the pins of the power connector to the holes in the cut piece of rope light. Thread the other platic nut over the end of the rope light as shown.

Slide the rope light onto the pins making sure the connection of the pins of the connector and the wire inside the rope light is secure. Cutting Rope Light First make absolutely sure that the main voltage is not connected. Measure the desired length and cut at the nearest cutting mark - picture 1.

Custom cut rope lights are custom measured and cut based on your length specifications to the nearest cutting increment of the rope light. Custom cut rope lights are UL-listed and include a UL power cord power connector and an end cap. No other accessories are included.

All custom cut rope light sales are final. Kits Rope light kits come in premanufactured UL-listed lengths and include gasketed screw. Rope lights are one of the finest lighting options of the 21st century.

LED rope lights are flexible durable and have an average lifespan around 100000 lighting hours. However one of the best things about LED rope lights is splicing. This will allow you to use different colors in one stretch replace specific defunct sections or extend the length of your rope light.

Be sure to make a smooth and clean vertical cut. The sharper your cutting blade is the easier it will be to cut the rope light. Once you have made your cut you will need to trim the inner wires to allow room for the connectors to insert correctly.

Bend the end of the rope light sharply to the side. If you are going to illuminate the base of a rock wall with few turns for example then you may want to use 12 inch. This could also work with a walkway.

However if your application requires some tight turns and twists or if you prefer the rope light. Not exactly but I am using around 900 of rope light and have had to splice in a new piece here and there. I am guessing you know how to find the cut marks on rope light.

You just need to cut out the bad sections. I would cut it at each end of the dead lights. You say 4 out then 4 good then 4 out I would cut out the whole 12 and splice in.

Cutting Take the rope lighting and observe it carefully. You will find marks that indicate the locations where the lighting can be cut do not cut the rope lights at unmarked locations. Cut the rope lights according to your need at appropriate locations.

Cut the lighting properly you can use a pair of scissors or a rope cutting tool to do.