05
Feb
He set the propshaft at around 4 inches below the. In this program were going to talk about how to properly fill and purge a manual hydraulic steering system.
You can have one person stationed back here at the steering cylinder.
How to fill hydraulic steering on boat. Remove the vent plug from the top of the helm. Screw the threaded end of the filler tube into the helm filler port. Remove the cap from the steering fluid oil bottle and holding upright screw into the filler tube bottle cap.
Turn the oil bottle upside down and poke a hole in the bottom of the bottle. How to Add Fluid to Hydraulic Steering. Thread filler tube into helm pump.
Thread bottle of fluid onto filler tube. Poke a hole into the bottom of the bottle or cut the bottom off and create a funnel. Turn bottle upside down like an IV.
Boating Tips Tricks Hydraulic Steering - Checks and topping up your fluid - YouTube. How do i go about filling the steering for a hydraulic set up. I purchased the system used and when i took it off the boat the hydraulic fluid leaked everywhere.
I assume when i put it on my boat i need to add alot since alot leaked out. Steering tilt tube and re-grease using a good quality marine grease. Grease support rod liberally 4.
Grease all contact points shown in Figure 37. DO NOT remove tiller bolt to re-grease. Remove steering wheel and re-grease wheel shaft using a good quality marine grease.
Inspect hydraulic oil for cleanliness flush if required. Check the hydraulic fluid level inside the helm by unscrewing the fill plug and looking inside. The level should be 18- to ¼-inch below the lowest thread in the fill port.
If lower than this fill the helm to the proper level but avoid over-filling. Check the steering response when turning the wheel. It should respond within a quarter turn.
Three-line systems are typical of larger yachts and fill at a separate reservoir thats pressurized. Such systems are more complex to engineer but theyre easier to check and top-up with oil. You simply add it to the reservoir.
Of course you release the pressure first then pump it back up with an air pump. Most passive non-power assisted systems are set up to be between 5 10 turns lock-to-lock on the steering wheel and if we translate into to mechanical advantage it goes like thisWell use total rudder arc at 70 degrees about 15th of a full circle and seems most typical in most steering installation guides for this example If it takes 7 full 360 degree turns of the steering wheel to. How to Bleed Purge Boat Hydraulic Steering System - YouTube.
How to Bleed Purge Boat Hydraulic Steering System. In this video is how to check the level and bleed a Sea Star outboard hydraulic steering system. Bleeding a hydraulic system is purging it from air.
2 x Hydraulic Steering Fluid HA5430 1 x Filler Kit HA5438 It doesnt take very many tools to complete the install. You will need a three-inch hole saw to cut the dash area for the helm unit a 516-inch drill bit for the helm mounting bolts and of. Make sure to run hydraulic fluid through the hose first.
Attach a second hose from the steering cylinder fitting to another container to catch the overflow. If your boat is small enough you can use one container for the ends of both hoses. Make sure the container has enough extra room for overflow.
Turn the wheel back and forth from lock to lock. A hydraulic steering system is recommended for larger boats 10 metres and above in length and those moving at high speeds. The torque or force of a large outboard motor means it can be difficult to bring out of a turn or veer sharply from heading straight with mechanical steering.
Click to see full answer. Most boats have either mechanical or hydraulic steering systems. Choosing the right steering system for your boat depends on the size of the boat and the type and size of the motor.
You may be looking at upgrading your boats steering from a tiller steer outboard to mechanical steering or from mechanical to hydraulic boat steering. I have to disagree with Phil here. If you wait until you start noticing a problem it might be too late.
All that matters is that you have the helm pretty full. With the version with the oil plug on top of the helm pump the fluid should be about ¼ below the bottom of the threads. Any fuller and you will get some leakage when the temp gets.
Install the Hydraulic Steering. Connect the SeaStar hydraulic steering cylinder to the tilt tube and the tiller arm. The new hydraulic kit should include a tiller bolt and nyloc nut.
I bought a 97 201 PE with 225 hp Venom last August. I told the dealer that my preferences were comfort and drivability first and speed second. Since the fastest boat Id had before this would only run 40-45mph didnt want to kill myself the first time out in a hi-perf.
He set the propshaft at around 4 inches below the. Only use oil LS or oil with ISO 22 viscosity. Make sure that the hydraulic piping is perfectly clean and keep the oil free from impurities which may cause the deterioration of the components of your hydraulic steering system.
For more details please refer to the instructions provided with your product. How to Bleed a Boat Hydraulic Steering System Video Transcript. In this program were going to talk about how to properly fill and purge a manual hydraulic steering system.
First off youre going to need two people. You can have one person stationed back here at the steering cylinder.