How to fix rivets in aluminum boat

Some are mechanical involving resetting the rivets. Jon boat rivets exhibit different wear and tear over time caused by leaky aluminum boat riveting.

Prepare the sealing resin.

How to fix rivets in aluminum boat. How to replace rivets and repair holes in an aluminum boat. Things to Consider When Choosing Epoxy for Fixing the Leaks in Your Aluminum Boats Rivets. Steps on How to Repair Leaking Rivets on Your Boat.

Identify where the leak is. Prepare the sealing resin. Apply the epoxy mixture to smaller gaps.

Fill the bigger gaps in rivets. Clean the excess epoxy resins. Locate the leaking rivets.

Prop the boat up and spray water inside to locate the loose rivets. Dry thoroughly and sand the area around the rivets with 120 grit to remove any paint and provide some tooth for the epoxy. Etch the area with WEST 860 Aluminum Etch Kit.

Mix and apply a layer of GFlex epoxy. Use Screws that match the diameter of the rivets you want to use. The rest of the other types of repairs are hokey pokey.

And this is coming from a weldor that fixes alum. TRUSS HEAD phillips screws with flat washer and nylon locking nut on the back side. How to check aluminum boat for leaks and leaky rivets - YouTube.

Making the aluminum boat repair. With the leaks identified and marked here are the techniques used for the repair. Flip the boat over for easier access to the bottom and prepare the surface for bonding.

For the seams clean out any debris that might still be stuck inside. On the rivets I used a wire brush in a circular motion to abrade the surface. Jon boat rivets exhibit different wear and tear over time caused by leaky aluminum boat riveting.

Aluminum boat rivets may. Shag you do have to match rivets to boat. Not types of aluminum alloy.

Forget aluminum alloys but fir instance if the boat was 312 stainless you could easily use 316 stainless so long as it was stainless. But they have aluminum rivets with steel shaftsor what makes a pop rivet pop and that would be bad. Just purchased an older 22 aluminum boat.

Took it out on the weekend and took on some water Brought it home put some water in it and have 5 leaking rivets in same area all close to centre. Can anyone help with some fix tips or info on a good professional Thanks Oh by the way I got skunked this weekend on lake o and Erie Thanks Bill. Sand the aluminum lightly and then clean with 70 isopropanol let dry then just cover all the rivets and the seam with the PC-7.

You can get a smooth finish by wetting your finger in water and then smoothing the epoxy with your wet finger redipping finger in water as needed otherwise the stuff is really sticky. The first step in repairing this aluminum boats holes and leaky rivets was to use an angle grinder with a sanding disc to remove the silicon. A wire wheel or wire brush is also acceptable.

After removing the residual silicon Muggy Welds Super Alloy 5 rod and flux was applied with an oxyacetylene torch with a size 1 tip. Aluminum Closed end rivets for aluminum hull repair use them and you will be fine. That is what we are all using and there really is not enough time in our lives to worry about that rust and you can dab 5200 on the inside of the rivet after installed.

Apply a little extra on the high side of the rivets and let gravity help. Wait a couple days cover the rivet with something like MarineTex putty or Aquamend epoxy let it set then coat that putty with more Gluvit. Before touch up paint wash the repairs with 5050 vinegar and water and a scotch brite etch.

To qualify the above any chance to. There are multiple methods to repair leaking rivets on an aluminum jon boat. Some are mechanical involving resetting the rivets.

Some are chemical using a sealant around the rivets. All the methods have one thing in common. Before you begin the repair you fill the boat with water to find the leaks.

Use Gluvit on aluminum fishing boats to repair leaky aluminum seams and rivets. The cure rate has a long working time that allows penetration into cracks to seal and strengthen. Gluvit fills minor chips and pinholes and is easily painted with most bottom or topside coatings and paints.