14
May
Use glycerine silicone lube or dish washing liquid with a little water. Knicking the impeller gently in the rest of the way using the large socket and a piece of wood underneath.
The water is brought into the outboard through the use of an impeller that draws water into the water intake opening on the midsection of the outboard.
How to install an impeller. Tie an electrical cable-tie around the impeller. Tighten the cable-tie down until it draws in the impeller vanes into a contracted shape but not overly tight that it is difficult to remove. Press the constricted impeller into the pump housing.
As it slides into place the cable tie will come against the outer edge of the housing. How to replace an outboard impeller in 15 minutes water pump - YouTube. With electrical tape.
When installed properly with electrical tape the impeller should not easily fall off your boat. However check the tape regularly to make sure that it is still secured to the boat and is not beginning to peel off. Set the impeller on top of the hull in your selected location.
Sight down the length of the hull to ensure the. Begin by inspecting each end of the shaft to make sure there are no nicks or burrs on the ends of the shafting. Next inspect the impeller to make sure the bore size matches the shaft.
Go ahead and install the impeller on the shaft and then using the provided allen wrench tighten the set screws on the impeller. Install the water pumpimpeller into the housing in correct direction by pushing and rotating it so that all impeller blades face the same correct direction. All blades should be slightly bent to the right in the housing.
The woodruff key slot should be noted. This has been marked in orange to clarify the location. SEA DOO IMPELLER WEAR RING INSTALL - Replacing The Impeller and Wear Ring on 2008 Sea Doo RXT 255 - YouTube.
To install the impeller lube the entire exterior with glycerin. After lubing compress it with your fingers and seat it into the pump body. I often hear of folks talking of using zip ties to pre-compress the impeller for insertion but I honestly dont understand why one would need to do so.
Use a clean cloth to clean inside of pump of WD-40. Inspect pump and impeller for any damage. Install new impeller by hand.
DO NOT use petroleum jelly WD-40 etc. Use glycerine silicone lube or dish washing liquid with a little water. Use flat gasket and replace cover.
DO NOT OVER-TIGHTEN BRASS SCREWS as they can easily snap. Large socket under the impeller. After the 24 have been knocked down and the impeller is in the housing.
Knicking the impeller gently in the rest of the way using the large socket and a piece of wood underneath. The water is brought into the outboard through the use of an impeller that draws water into the water intake opening on the midsection of the outboard. The impeller may need to be replaced if the engine is not running properly.
You can install an impeller on a Force outboard motor by first accessing the impeller pump housing. Install the new impeller. Screw the impeller in by hand in a clockwise rotation making sure it glides on freely.
Once the impeller has bottomed out torque it to 90 ft-lbs. Using the impeller tool and torque wrench. Once the impeller is installed remove the.
Replace the Sea Water Pump Impeller Watch How To Video Impellers should be replaced every other year. It is important to realize that even with a new impeller just a small amount of scoring to the pump body can effect the output flow of the pump significantly. Place the new impeller inside the top casing in the correct blade orientation and insert the shaft key if so equipped.
Slide the casing down over the drive shaft and align it. This process is fairly simple and only requires a 10mm 12mm and 14mm socket a set of allen wrenches a pry bar a 1 116 th wrench and some marine grease. While many of you may have these tools in your garage marine grease can either be found online or at your local automotive store.
Correctly installed impellers may last for several years but you should stick to a schedule of preventative instead of emergency maintenance. What is the difference between impeller and propeller. Propellers and impellers both provide thrust but do it in different ways.
The easiest way of getting the impeller in the pump is to pull the pump from the generator a little bit place the impeller on top of the pump and twist it in the proper direction to get it started vane tips are trailing rotation then align the impeller with the flats on the drive shaft and slide it into the pump body.