How to install axle bearings

Install and tighten the axle. 5 Re-install the axle per manufacturers recommended assembly procedures.

You use the same procedure for properly setting up the gears for a 10- or 12-bolt regardless of the actual version you have.

How to install axle bearings. Axle repair bearing installation - YouTube. Rear Wheel Axle Bearing Installation. An instructional video demonstrating the proper installation techniques to use when installing a rear wheel bearing.

It also covers the basic operational principles of a few kinds of rear axle bearings. The bearings simply press on. The sequence of parts is the same as the original wheel bearings.

Drop the 5 hole retaining plate over the axle shaft. Grease the seal on the new bearings. Press the bearing tight against the axle flange with the seal facing the axle flange.

And old bearing parts. Non C-Lock axles 5. Remove the nuts holding the retainer plate to the backing plate ig.

Slide the retainer plate off of the studs. To prevent the brake backing plate from slipping off reinstall and inger tighten the lower nuts. Grip the axle shaft lange with a puller or slide hammer.

This is a short Video on the removal and install of axles and the bearings going from an Adjustable tapered bearing to a constant roller sealed bearing also kno 100 How-To Tutorials. 4 Install bearing in the axle housing with seal facing out. Assembly force must be applied to bearing ring and not to seal.

Striking or pushing on the seal will result in failure. A correctly installed bearing may extend out from the housing up to 14. 5 Re-install the axle per manufacturers recommended assembly procedures.

Lightly lubricate the axle bore with new gear oil to ease installation. Using a bearing race installing tool or an appropriately sized socket tap the new bearing into the axle. Flange prior to installation of the bearings and ring gear.

Install the differential bearing cones onto the bearing hubs of the. Differential case using the proper installation tool. Many Dana applications use.

Shims between the bearing cone and the differential case bearing hub shoulder. The bearing cones must be. Easy to install.

As for leaks Be sure to lube the seal so the axle slids and dont tare it. Been in there. If I had to guess.

Installed when I put the 373s in. The axles werent real bad but you could feel the lip where the bearing rode. And axle had updown play.

To compensate for the seal the O ring is used in the bearing bore to seal the outside of the axle bearing against the axle flange. The factory axle flange where the bearing rides has to be clean and not buggered up. I smear a little petroleum jelly on the O ring to help with the installation.

Installing an Axle Assembly and Differential Step1 Measure Width of Shims. You use the same procedure for properly setting up the gears for a 10- or 12-bolt regardless of the actual version you have. The only differences are a few of the settings specs which vary by version and year.

You start the procedure by setting pinion depth. Install Purchased Pair of Axle Bearings. Labor Charge Only Bearings sold separately.

Professional installation of axle bearings on Strange axles. Cold pressed bearings locking collars. Pre-heating not recommended as collars can lose holding power.

Never tack-weld collars as damage to the axles heat treat can occur. Probably the easiest way to get the best information to you is to give you a link to the Dana Ezgo rear axle repair manual. It shows the steps to replace the wheel bearing and has photos of what you need to do.

The manual shows all repairs for the rear axle. After everything is removed clean up the carrier and get it ready for the bearings. I froze the bearing heated up the carrier and greased the area where the bearing when in to make it a little easier.

Flip it over and put the axle spacer sleeve in. I greased inside and out using a plumbing flux brush. Install the new rear axle bearing and collar.

Press the collar and bearing assembly onto the axle shaft. Reinstall the axle shaft into the axle shaft housing. Spin the axle shaft until the splines match up with the gears in the differential.

Install and tighten the axle. Tap the axle shaft in the center of the axle face with a mallet to install it. The grease on the seal will help it to slide in freely.

You may have to give the axle several firm hits with the mallet to seat it all the way into the housing. Once the bearing race has bottomed out in the housing end you will. Use one hand and push your palm to one side of the rotor while holding your other hand under the outer bearing.

This force will pop the outer axle bearing and washer outward be ready to catch the bearing. New axle bearings and seals are recommended whenever axles are replaced. Consult your Strange Engineering representative or the application guide to determine whether lock rings andor other hardware will be required.

Sealed ball bearings and sealed double row ball bearings are typically sold as a sealed bearing.