How to lube steering cable on boat

Steering cable lube. Disconnect the steering link at the motor and check by turning the wheel if still stiff you can try greasing but most likely the cable is going.

Can you lubricate a boat steering cable.

How to lube steering cable on boat. With your grease gun lubricate the cable with the new grease fitting. Be sure to only use the recommended marine grease by the manufacturer. How To Remove Gas From Boat Fuel Tank in Quick and Easy Steps.

Important Things To Remember. This task of lubricating your steering cable involves dealing with power tools. With all the other maintenance you do on your boat dont wait until the boats cable steering begins to tighten up before you lubricate the point where the steering cable interacts with the motor.

Thread a piece of extra fine sandpaper into the rod from a firearm bore cleaning kit attach the rod to a drill and put the tube into a bench vice to hold it tightly. If I can seal around the pivot tube end of the cable using 2 PVC which is long enough to let the cable travel in and out a compression fitting around the cable sleeve for the 2 pipe to attach and a threaded PVC cap on the other end with a male air chuck screwed into it then I could fill the 2 pvc tube which will be about 24 long with WD40 or better cleaner and inject it under pressure into the sleeve and around the cable. The SafeT QC system is a three turn lock to lock steering package.

If your older system needed more turns the new one may feel harder to turn. You should also check that the cable does not have bends smaller then the recommended radius no kinks and that the steerer rod attachment to the motor is alligned correctly. If the cable end is impossibly stuck in the tilt tube it is time to phone a friend and seek professional help.

If the cable end comes out of the tilt tube and this fixes the problem then clean the tilt tube lubricate the cable end with marine grease and reassemble the steering. Move to the Helm. Its lubed from the back by the rudder itself.

Turn your wheel all the way in the direction that the cable is all the way out. One way it will be all the way in and the other way about 12 or so of the shinning cable will be sticking out. Use a spray lube on the shinng cable that is sticking out.

Then work the wheel back and forth. Steering cable lube. Tags cable lube steering.

Jump to Latest Follow 1 - 16 of 16 Posts. Cause its gonna bite you when you least expect it. Being unable to make your trip or unable to steer your boat both unacceptable scenarios IMO.

U pper M idwest P ower B oat A ssociation. Place a container beneath the bottom end of the cable to catch the oil that should eventually drip out of the lower end of the jacket. Allow the cable to hang until the oil drains through.

Slide and rotate the cable in the jacket then give the bag a second shot of oil it can be the same oil to assure a thorough lubrication. Can you lubricate a boat steering cable. Pull the steering cable out of the tilt tube.

If the tube has internal corrosion that makes the cable difficult to remove liberally spray a water-excluding lubricant into the tilt tube and wait an hour before removing the cable from the tube. Clean any hardened marine grease from the inside of the tube by spraying the inside of the tube with a penetrating lubricant. Thread a piece of extra fine sandpaper into the rod from a firearm bore cleaning kit attach the rod to a drill and put the tube into a bench vise to hold it tightly.

2 The cable itself can get very stiff over time especially if left in one position. The best way I have found to lube it is to remove the cable from the boat and hang the cable from the steering head end. A small funnel and plasticene can be used to hold oil at the top of the cable.

One of the first steps you need to take to lubricate the steering linkages of your Mercury outboard motor is to rotate steering wheel to fully retract steering cable end. The second step to lubricate the steering linkages of your boat requires you to connect the grease gun and locate the tilt lever grease fitting. And finally for the last step you need to connect to swivel pin grease fitting and lubricate using lightweight oil on the steering.

The idea is to attach the hose over the steering cable with the clamps fill the hose with synthetic oil thread in the valve stem secure it with a clamp and then pressurize with a bicycle pump. The pressure forces the oil through the cable casing to lube the cable. And grease it an O-ring wipes all the grease off as it retracts into.

When I disassembled the system the steering rod was. Dry as a bone. While installing the new system I cleaned the tilt tube out with.

Engine cleaner and a wire brush. I then ran pieces of an an old. The fix for this is to remove the smaller hex nuts holding the steering links at either end of the hydraulic ram and pull them out of the steering tube.

Next thoroughly clean the links and the inside of the steering tube with a wooden dowel with a solvent soaked rag wrapped around it. Nov 11 2005. Teleflex Rack Steering - Can I grease it.

Disconnect the steering link at the motor and check by turning the wheel if still stiff you can try greasing but most likely the cable is going. Always replace steering cables that are stiff in operation or have damage to the plastic jacket outer casing. Clean and lubricate the engine tilt tube or cable support tube and the steering cable telescopic output ram as follows.

Remove the steering cables telescoping ram from the tilt tube. Clean the tilt tube inside diameter thoroughly. New power boat owner and trying to learn all the mechanical stuff so Im likely to ask lots of dumb questions.

Ive got a 5L Mercruiser A1 sterndrive. Wanted to lubricate the steering actuator valve like my manual and Seloc tell me to. Found the zirc fitting.