How to lube steering cables on boat

I spent over 30 min just trying to drill. When you extend the steering rod and grease it an O-ring wipes all the grease off as it retracts into.

A small funnel and plasticene can be used to hold oil at the top of the cable.

How to lube steering cables on boat. With your grease gun lubricate the cable with the new grease fitting. Be sure to only use the recommended marine grease by the manufacturer. How To Remove Gas From Boat Fuel Tank in Quick and Easy Steps.

Important Things To Remember. This task of lubricating your steering cable involves dealing with power tools. Steering cable easy fixlubricate.

The zercs on the tilt tube are for the motor joint not the steering. You have to pull the cable out of the tilt tube and clean and lubricate the tilt tube. Cable has no means of being lubricated.

The idea is to attach the hose over the steering cable with the clamps fill the hose with synthetic oil thread in the valve stem secure it with a clamp and then pressurize with a bicycle pump. The pressure forces the oil through the cable casing to lube the cable. Always check your steer tube for adjustment the tendancy is to overtighten the bushing nuts and the steer tube must move ever so slightly back and forth to compensate for the swing of the tiller If the tube is too tight it will cause the steering to bind and be stiff A good working rack should be pinky finger operation out of the water Also having a swivel clevis about 20 bucksat the end of the.

Its lubed from the back by the rudder itself. Turn your wheel all the way in the direction that the cable is all the way out. One way it will be all the way in and the other way about 12 or so of the shinning cable will be sticking out.

Use a spray lube on the shinng cable that is sticking out. Then work the wheel back and forth. Place a container beneath the bottom end of the cable to catch the oil that should eventually drip out of the lower end of the jacket.

Allow the cable to hang until the oil drains through. Slide and rotate the cable in the jacket then give the bag a second shot of oil it can be the same oil to assure a thorough lubrication. With all the other maintenance you do on your boat dont wait until the boats cable steering begins to tighten up before you lubricate the point where the steering cable interacts with the motor.

Thread a piece of extra fine sandpaper into the rod from a firearm bore cleaning kit attach the rod to a drill and put the tube into a bench vice to hold it tightly. The SafeT QC system is a three turn lock to lock steering package. If your older system needed more turns the new one may feel harder to turn.

You should also check that the cable does not have bends smaller then the recommended radius no kinks and that the steerer rod attachment to the motor is alligned correctly. The best way I have found to lube it is to remove the cable from the boat and hang the cable from the steering head end. A small funnel and plasticene can be used to hold oil at the top of the cable.

You will notice that the cable inner has a spiral winding around its core. Our steering cable started to become very stiff. We eneded up replacing the entire cable which made a HUGE difference.

EnjoyIf you enjoy the content and wan. Just a little grease and light oil applied as demonstrated in this Mercury Quick Tip will not only help your engine have a long trouble-free life it will also ensure your steering is smooth and responsive every time you hit the water. If the cable end comes out of the tilt tube and this fixes the problem then clean the tilt tube lubricate the cable end with marine grease and reassemble the steering.

Move to the Helm. I attempted to lube my steering cable like that and i could not drill through the housing. I spent over 30 min just trying to drill.

Ended up replacing the cable myself and it was only 140 bucks wshipping. But if you really wanna give lubing a try you need something better than wd-40. The best thing is ship to shore but a good alternate is liquid wrench.

Drill into the cable under the dash. Clean any hardened marine grease from the inside of the tube by spraying the inside of the tube with a penetrating lubricant. Thread a piece of extra fine sandpaper into the rod from a firearm bore cleaning kit attach the rod to a drill and put the tube into a bench vise to hold it tightly.

Lubricating Steering Linkage on a Mercury Outboard Motor. When lubricating steering linkage on a Mercury outboard motor it is essential to ensure a peak performance for your outboard motor. Here at Modern Boats Sales Service we think bringing you these easy steps and mechanics to achieve maximum performance from your boat is essential for long life of your outboard.

My steering was stuck solid so I disassembled and removed the entire assembly and replaced it with a new Teleflex Safe-T steering system. I think I figured out why the steering stuck despite the fact that I grease the steering rod regularly. When you extend the steering rod and grease it an O-ring wipes all the grease off as it retracts into.

How do you lubricate a boat shift cable. Pour enough motor oil into the bag to fully submerge the end of the cable jacket and zip the bag closed. Place a container beneath the bottom end of the cable to catch the oil that should eventually drip out of the lower end of the jacket.

Allow the cable to hang until the oil drains through. Always replace steering cables that are stiff in operation or have damage to the plastic jacket outer casing. Clean and lubricate the engine tilt tube or cable support tube and the steering cable telescopic output ram as follows.

Remove the steering cables telescoping ram from the tilt tube. Clean the tilt tube inside diameter thoroughly.