How to lubricate throttle cables

Then use a lubricant designed for throttle cables. Place the cable upright and pour a small amount of oil into your cone.

I do this once a year and Ive only ever had to replace 1 cable in the 15 bikes Ive owned.

How to lubricate throttle cables. It will ensure a smooth throttle action and prevent the chance of the throttle getting stuck wide open. In order to clean first spray off the dirt using compressed air and a light degreaser or brake cleaner. Then use a lubricant designed for throttle cables.

My two favorites are dri-slide and sprayable gel lube. This video will show you the fastest way to lube your brake throttle clutch or any other cable you may haveDont have a cable lube tool. Do you have a p.

Basically you clamp a rubber stopper over one end of the cable insert a tube from a can of silicone-based cable lubricant into a little hole and give the nozzle a squeeze. The cans pressure forces the lubricant through the cable. Apply the lubricant in short bursts until the bottom end of the cable begins to bubble or drip.

Thankfully not much you dont have already. Prepare the Work Area. Remove the Clutch Lever.

Slip on the Cable Luber. Lube the Clutch Lever Cable. Reinstall the Clutch Lever.

Disassemble the Throttle Cable Housing. Lube the Throttle Cables. Place a container beneath the bottom end of the cable to catch the oil that should eventually drip out of the lower end of the jacket.

Allow the cable to hang until the oil drains through. Slide and rotate the cable in the jacket then give the bag a second shot of oil it can be the same oil to assure a thorough lubrication. Throttle now turns very easily.

To lube the cable make a small cone out of aluminum foil. Put the cone over the end of the cable and use an elastic to make a seal. Place the cable upright and pour a small amount of oil into your cone.

Our expert takes apart the housing to lubricate the throttle cablesFor more of our Harley videos visit httpbitly2e7WiQx. In this MC Garage Video. Two slick ways to lubricate your control cables.

If your bikes clutch throttle or brakes are feeling sticky its likely time to. Spray lubricant into the 2 throttle tubes shown with arrows in step 8 where the throttle cable enters the tubes. Turn the throttle grip by hand back and forth to help work the lube along the cable.

Clean up any excess mess and reassemble in the reverse order of which was disassembled. Beside above how do you lubricate an outboard throttle cable. Pour enough motor oil into the bag to fully submerge the end of the cable jacket and zip the bag closed.

Place a container beneath the bottom end of the cable to catch the oil that should eventually drip out of the lower end of the jacket. Allow the cable to hang until the oil drains. Lubricate with Rust Inhibitor.

Clutch Cable Throttle Cables Lubricate the cables by seeping the oil between the cable and housing. The cable may be lubricated by using a commercially available pressure cable lubricator with an aerosol cable lubricant or chain lube. With the cable disconnected at both ends the inner cable.

Ive heard of people tying a baggie of WD40 or similar around the cable end and hanging it allowing the lube to dribble through the cable jacket thereby saving the cable. I usually find that the plastic jacket cracks before the actual cable goes bad in which case this aint gonna help much. Personally I just buy new ones.

Hold the cable upright and fill the bag with oil. Leave it overnight and itll lube the whole cable by gravity. I do this once a year and Ive only ever had to replace 1 cable in the 15 bikes Ive owned.

Sent from my iPad using Tapatalk. How To Lubricate A Cable - Prevent Cable From Freezing - YouTube. ANGLE 61 ALLIE PHVID3.

You just take off the two side panels and remove the seat by two allen bolts on either side and then the back of the tank has a bolt under the front of the seat. Loose the two bolts under those plastic black straps by the forks at the front of the tank and you can lift the tank up enough to access the throttle cables. You can search for a better detailed step by step method of how to remove the tank on these forums and its really easy.

I had to reroute the throttle cables. Remove the uppertop cable end. Wrap a rag around the lower cable end.

Poke a small hole in the corner of a Zip-Loc resealable bag. Thread the cable into the bag so that the sheath is about 14-12 inside the bag. Tape around the cable where it enters the bag to seal it.

Add a tablespoon or so of oil. Some like motor oil I prefer gear oil as. Attach the Cable Lube Tool with red feed tube onto the cable.

One end of the Cable Lube Tool will have a larger opening. This one fits over the end of the cable sheath. The other end fits around the movable cable.

Attached the spray can to the red feed tube. Depress the spray button. Do NOT press it more than 1 or 2 seconds or excess lubricant will spray out into the passenger cabin.

If you want wrap a shop rag around each end of the throttle cable.