How to remove bearing buddies

Etrailer Bearing Buddy Bearing Protectors Installation - YouTube. I am trying to pull the hubs to grease the bearings and replace the seals but I cant get the Bearing Buddies off.

Basically when servicing the hubs you need to remove the dust caps or bearing buddies without rocking or tilting the buddies in the ends of the hubs.

How to remove bearing buddies. How to remove a Bearing Buddy bearing protector. Bearing Buddy Removal Installation Trailer - YouTube. Pull the bearing buddy off of the hub and set it on the paper towel.

Repeat the previous five steps to remove the bearing buddies from the other trailer wheels. Wwwaakronboatsconz Aakron Marine is one of New Zealands largest suppliers of inflatable boats boat trailers and outboard motors with a strong foothold i. Bearing Buddies like BB2441 fit very tight into a trailer hub.

In order to get them out you will need to use a rubber mallet and persuade them out. Once the Bearing Buddy starts to unseat from the hub you can grab it and wiggle it out. The best way to remove a Bearing Buddy Bearing Protector like BB2717 is pretty much what youve been doing.

Because the fit inside the hub bore is pretty tight you just have to take a rubber mallet or wood block and firmly tap it around the sides until its unseated and loosened up enough to pull it out by hand. Removing bearing buddies to get the bb off jack up the wheel take a block of wood and a hammer and start hitting the outside edge of the bearing buddy while turning the wheel slowly until it works its way off When using the block of wood dont worry about hurting any thing hit that thing as hard as you need to until she pops off. I am trying to pull the hubs to grease the bearings and replace the seals but I cant get the Bearing Buddies off.

Do all oil hubs have threaded dust caps. I can turn the Bearing Buddy using a pipe wrench a little bit but they will not turn off. Hammer the Bearing Buddy into place with a rubber mallet.

Whack the Bearing Buddy around all sides until it sits flush over the bearing. A rubber mallet will prevent any damage to the Bearing Buddy. Remove Old Bearing Buddy Using Ice And Cold Beer - Boat Trailer Repair - YouTube.

When the hubs get bell shaped the bearing buddies fall out. Basically when servicing the hubs you need to remove the dust caps or bearing buddies without rocking or tilting the buddies in the ends of the hubs. If you rock the buddies or dust covers the hubs can easily get bell shaped.

Bearing Buddy explanation Greasable axle spindle - YouTube. Etrailer Bearing Buddy Bearing Protectors Installation - YouTube. Then he places a block of wood over the end of the Bearing Buddy.

The block of wood disperses the force of the hammer used to tap it into place. To remove a Bearing Buddy I would use a rubber mallet and gently tap it on the sides to unseat it. Helpful expert reply by.

Ask The Experts a Question. To remove Bearing Buddy lay a block of wood against the side of it and strike the wood with a hammer. Place the wood on the opposite side and hit again.

Continue this procedure until you walk the Bearing Buddy out of the hub. Dont disassemble the Bearing Buddy to attempt to remove. The great thing about Bearing Buddy like part BB1781 is that when you add grease to your system with the included fitting it will move the spring-loaded piston outward and allow grease to seep around the edges to keep from damaging the seal.

You can manually check the Bearing Buddy to be sure it has enough grease. All you need to do is press the edge of the piston. Many opinions on this but for easy loader spindles i dont recommend bearing buddies.

The rubber plug expansion with heat and contraction with cooling keeps water out. No weep hole open. Bearing Buddy is nothing but a glorified grease cap with a spring that maintains some positive pressure.

If your bearings havent been repacked within the past 2 to 3 years its time. Knock the BB off with a rubber mallet disassemble the hub and inspect and repack the wheel bearings. Bearing Buddy is held in the hub by an interference fit.

To remove Bearing Buddy lay a block of wood against the side of it and strike the wood with a hammer. Place the wood on the opposite side and hit again. Continue this procedure until you walk the Bearing Buddy out of the hub.

Dont disassemble the Bearing Buddy to attempt to remove it. Using a Bearing Buddy to grease a hub can easily allow you to over fill the hub and blow out a seal. The zerk fitting where you insert the grease is sitting on a spring loaded disc or piston that will move outward away from the hub as grease is added.

Push on the edge of the piston with your finger. If the disc doesnt move add grease until. How Genuine Bearing Buddy Works.

The axle hub is filled with grease until the grease forces the Bearing Buddy piston outward about 18 inch. Because the piston is spring loaded the piston exerts a slight 3 PSI pressure against the grease which maintains a slight pressure between the inside of the hub and the outside environment.