How to remove bearing buddy

Continue this procedure until you walk the Bearing Buddy out of the hub. Push on the edge of the piston with your finger.

Photo Of Removing The Dust Cover Or Bearing Buddy With A Screwdriver Trailer Tires Trailer Trailer Axles from www.pinterest.com

Since I have to replace the mangled dust cap should I just take the zerk off the axle and add bearing buddies.

How to remove bearing buddy. How to remove a Bearing Buddy bearing protector. Bearing Buddy Removal Installation Trailer - YouTube. Pull the bearing buddy off of the hub and set it on the paper towel.

Repeat the previous five steps to remove the bearing buddies from the other trailer wheels. Wwwaakronboatsconz Aakron Marine is one of New Zealands largest suppliers of inflatable boats boat trailers and outboard motors with a strong foothold i. Remove Old Bearing Buddy Using Ice And Cold Beer - Boat Trailer Repair - YouTube.

The best way to remove a Bearing Buddy Bearing Protector like BB2717 is pretty much what youve been doing. Because the fit inside the hub bore is pretty tight you just have to take a rubber mallet or wood block and firmly tap it around the sides until its unseated and loosened up enough to. I can turn the Bearing Buddy using a pipe wrench a little bit but they will not turn off.

I can get it to rock back and forth using a hammer but not very far. Not sure if these are threaded or pound on. Bearing Buddies like BB2441 fit very tight into a trailer hub.

In order to get them out you will need to use a rubber mallet and persuade them out. Once the Bearing Buddy starts to unseat from the hub you can grab it and wiggle it out. Ask The Experts a Question.

Hammer the Bearing Buddy into place with a rubber mallet. Whack the Bearing Buddy around all sides until it sits flush over the bearing. A rubber mallet will prevent any damage to the Bearing Buddy.

Having had no instruction in this either I cut a small piece of an inner tube about 2 x 4 and grabbed a small pipe wrench. I wrapped the piece of inner tube around the bearing buddy placed the pipe wrench on it and wiggled not turned the bearing buddy out. Removing bearing buddies to get the bb off jack up the wheel take a block of wood and a hammer and start hitting the outside edge of the bearing buddy while turning the wheel slowly until it works its way off When using the block of wood dont worry about hurting any thing hit that thing as hard as you need to until she pops off.

Then he places a block of wood over the end of the Bearing Buddy. The block of wood disperses the force of the hammer used to tap it into place. To remove a Bearing Buddy I would use a rubber mallet and gently tap it on the sides to unseat it.

Helpful expert reply by. Ask The Experts a Question. To remove Bearing Buddy lay a block of wood against the side of it and strike the wood with a hammer.

Place the wood on the opposite side and hit again. Continue this procedure until you walk the Bearing Buddy out of the hub. Dont disassemble the Bearing Buddy to attempt to remove it.

Etrailer Bearing Buddy Bearing Protectors Installation - YouTube. Bearing Buddy explanation Greasable axle spindle - YouTube. All you need to do is press the edge of the piston.

If you can move or rock the piston it has enough grease. I have attached a drawing of a Bearing Buddy you can check out to see what the components are. I have attached a link to our product page for Bearing Protectors you can check out.

Using a Bearing Buddy to grease a hub can easily allow you to over fill the hub and blow out a seal. The zerk fitting where you insert the grease is sitting on a spring loaded disc or piston that will move outward away from the hub as grease is added. Push on the edge of the piston with your finger.

If the disc doesnt move add grease until. But in the process of getting the dust caps off I mangled one so far. When removing it I see that there is a zerk fitting on the axle and just a rubber seal and dust cap.

Since I have to replace the mangled dust cap should I just take the zerk off the axle and add bearing buddies. Anyone know if this is ok i assume it is but want to check. Bearing Buddies are removed by gently tapping them off with a rubber mallet or hammer.

If you use a steel hammer hold a piece of wood against the Bearing Buddy and tap it to prevent damage. Protective grease caps with a flange resting against the hub can be removed with a screwdriver. Clean the Bearing Buddies or caps and set them aside.

Bearing Buddy is held in the hub by an interference fit. To remove Bearing Buddy lay a block of wood against the side of it and strike the wood with a hammer. Place the wood on the opposite side and hit again.

Continue this procedure until you walk the Bearing Buddy out of the hub. Dont disassemble the Bearing Buddy to attempt to remove it. How Genuine Bearing Buddy Works.

The axle hub is filled with grease until the grease forces the Bearing Buddy piston outward about 18 inch. Because the piston is spring loaded the piston exerts a slight 3 PSI pressure against the grease which maintains a slight pressure between the inside of the hub and the outside environment. Bearing Buddies are removed by gently tapping them off with a rubber mallet or hammer.

Brake drum removal with buddy bearing. You should be able to get the bearing buddy off without taking off the nut. The instructions say to place a block of wood on one side of the chrome protector and hit it with a hammer.

Then move the block of wood to the other side and do the same. Repeat the process from side to side and the collar.