How to replace steering cable on an inboard boat

Several boat mechanics wanted 700 just to replace the cables. When you have removed the steering arm go ahead and clean off marine grease that has hardened in the tube.

If the cable end comes out of the tilt tube and this fixes the problem then clean the tilt tube lubricate the cable end with marine grease and reassemble the steering.

How to replace steering cable on an inboard boat. I have replace steering cables on IO before but never on an inboard. I have an 85 mastercraft and the steering is tight. I do not see the part number on it but have been told it is a 14ft cable.

Does anyone know what the correct lenght is before I order. What are the basic steps to changing the cable. 1 At the rudder area disconnect the end of the steering cable from the tiller arm.

2 Loosen the large nut attaching the steering cable to the aluminum support tube these can be very tight and require an additional pipe wrench to hold the. Before you pull the old cable out of the boat attach a messenger line at the steering wheel end so that when you pull the old cable out from the engine end you will have threaded a messenger to help install the new replacement cable. Remove the steering cable from the tilt tube.

Clean the tilt tube inside diameter thoroughly. Remove corrosion in the tilt tube with a wire brush. Wipe until all loose material is removed.

Lubricate the tilt tube with a good water-resistant grease. Scour the steering cable telescopic ram with a brass wire brush and wipe until clean. If the cable end is impossibly stuck in the tilt tube it is time to phone a friend and seek professional help.

If the cable end comes out of the tilt tube and this fixes the problem then clean the tilt tube lubricate the cable end with marine grease and reassemble the steering. Move to the Helm. When you have removed the steering arm go ahead and clean off marine grease that has hardened in the tube.

Spray the inside with a good quality lubricant that can easily penetrate in this section. Grab a rod and thread a small sandpaper into it and attach your rod securely to the drill. Replacing a boat steering cable can be challenging but its a repair that is totally doable for the mechanically-inclined boat owner.

How to remove steering cable from 1984 inboard omc sterndrive housing. Sometimes things that you think will be really complicated end up being easy to fix. The Marine Mechanic Im going to connect you with knows all the tricks and shortcuts.

You measure the plastic jacket end to end but in this case you add 30 inches and then round up to the nearest foot again. For a new steering system installation on a stern drive application youre going to need to have three dimensions to get the cable length correct. Firmly press the injector fitting of your grease gun onto the boats steering cable nipple grease fitting and squeeze or pump the grease guns handle in order to generously lubricate the steering cable.

Keep pumping the grease until it oozes out around the guns injector fitting and the nipple. Either way you want to replace your boat steering cable system for safety and comfortability. Get a reliable inboard rack or rotary steering system today from Discount Inboard Marine.

1982-1990 Correct Crafts use a proprietary 17-12 cable that is only available from a CC dealer. 1991-92 use a Morse rotary 19-12 and 93-97 use an old style Teleflex rack 19-12. Grease the part of the cable sheath that passes through the steering cable guide tube with heavy marine grease.

Push the cable through the steering cable guide tube. Back at the transom assembly your cable goes into the control valve assembly. At the end of the output shaft of the cable it is attached with a cotter pin and clevis pin.

Remove the cotter pin and pull the clevis pin. Then unscrew the large aluminum nut that holds the cable to the assembly. You can now pull the steering cable out.

Replace the steering cable if the cable nuts on both ends are tight. Remove both cable nuts and the old steering cable and sheath leaving the old mounting brackets along the side of your boat in place. Install the new cable using the old mounting brackets and tighten both cable nuts.

19 MasterCraft Steering Cable. When the steering on your boat gets stiff its time to replace the steering cable. This 19 Steering cable is a direct replacement for Many MasterCraft boats produced from 1999 to 2012.

A new steering cable helps keep your boat operating in peak performance and allows for maximum maneuverability. As I researched replacing my cables I decided that it was probably time to replace the helm too ie. The part under the steering wheel - it contains the pinion gear.

Several boat mechanics wanted 700 just to replace the cables. It would have cost me 1000 to have them replace the cables and the helm. After doing some reading on the net.

Last winter I replaced my steering on my 2002wa and the motor was just to be lifted up enough to clear the transom and back about 4 inches then move to the port side about about 6 and the cable should pull out of the tube and pull the whole cable out from the helm end. When I replaced. Remove Your Boat Steering Cable.

Removing your steering cable is relatively easy. Simply disconnect the cable from the steering helm and from the engine using a wrench to loosen bolts that are holding it. Next find a rope that will be used to assist you in pulling the cable back through the boat.