02
Sep
If you check out the install video I attached you will see this done. Fortunately almost all wires you need except for a brake controller wire connect to your vehicles tail light assembly.
When no other solution works and you keep discovering corroded parts it is possible to purchase a wire harness for a reasonable price.
How to replace trailer lights. And how to completely rewire itRated Reds Luke Williams shows you how to replace the lights on your trailer___Check this outhttpratedredtvyoutube_. Some lights may not be user-serviceable such as some LED types and sealed waterproof lights but usually trailer lights that use standard incandescent bulbs have either a removable lens that either snaps into place or that is held in by screws. Examples of such lights are ST51RB and 432200.
You can use the link provided to see all trailer tail. It sounds like your trailer has the 6-12 inch Oval stop turn and tail lamps and some side marker lamps that use a rubber grommet like the 6-12 inch oval tail lights grommet A70GB. Since the area where your lights are mounted is not accessible from the back side you will need to pry the light out of the front of the grommet with a small screwdriver or other similar tool.
Our installer here will spray the light with some lubricant around where the light meets the grommet and then will use a screwdriver to pry the light out first and then the grommet. If you check out the install video I attached you will see this done. How to Wire Trailer Lights.
Video tutorial on how to wire trailer lights. So here I have an older trailer which needed some work along with re-wiring the lights. This is a fairly simple setup no license plate light or clearance lights.
Be sure to check with your local laws. The lights in the kit are not only easy to mount and dismount Blazer also designed the product with a pop-out bulb assembly for quick bulb changes. Step 1 Pull out the bulb assembly on the side of the light.
Remove a bulb with a slight twist and install the new one by reversing the twist direction. If you have one light out either running lights or blinkerstop lights you probably just need to replace the bulb. Remove the lens replace the bulb and check it.
If it works youre on your way. All you have to do is hook up your new LED lights using the following information. Brown is for tail lights.
Green is for stop and turn. White is for ground. The 2 extra wires on the tail lights are white and they are used for the ground.
Ask The Experts a Question. Open the driver-side door and pull the cover off the fuse block to access the puller. To change the fuses open the hood and locate the fuse box in the driver side of the engine compartment.
Remove the cover from the fuse box and set it aside. The fuses that control. LED Hooded License Light.
WhiteRed 18 Conspicuity Strips. Identification Light Bar with White Steel Base Red. 3-1316 Round Stick-On Reflector Amber.
3-1316 Round Stick-On Reflector Red. 4 Round Flange Mount STT Light. Yes you just have to remove the old lights match the wires and mount the new ones.
Please note that it is usually not a good idea to mix LEDs and incandescent lights so if you have have side markers or other lights on the trailer make sure you switch those to LEDs as well. Incandescent lights draw much more amperage than LEDs do. If there are absolutely no provisions for trailer lights you are electrically inclined or have a rough idea of how to wire trailer lights you might consider splicing into your existing wiring.
Fortunately almost all wires you need except for a brake controller wire connect to your vehicles tail light assembly. The last plausible solution would be to replace the entire light system on the trailer. You should not hesitate to change the trailers entire wiring if it appears to be extremely corroded.
When no other solution works and you keep discovering corroded parts it is possible to purchase a wire harness for a reasonable price. Demonstrating the proper technique for replacing and repairing broken RV marker lights Dave Solberg walks you step by step through the removal and installation process. Whether broken RV marker lights simply require a new casing or bulb or the socket needs to be replaced a job like this can be completed in no time so you can get back out on.
If all trailer running lights are out and the tail lights do not light up the issue is probably not bad bulbs. To rule out the simplest solution however check the trailer tail light bulbs and replace if.