How to seal aluminum boat

All the methods have one thing in common. Apr 19 2016 - There are multiple methods to repair leaking rivets on an aluminum jon boat.

Aluminum boats are corrosion resistant but they are not corrosion proof.

How to seal aluminum boat. Follow the directions of your boat sealant to ensure a proper cure. This often requires keeping the boat in a stable place to cure overnight. After that you should inspect the seal and test to see if its waterproof.

Need for more aluminum boat care products to help sustain your boating lifestyle. Keep browsing everything available here at BoatLIFE. How to seal rivits on aluminum boat To do the job right.

Replace any leaking rivets then use the Gluvit on the inside. Check your transom wood for rot now and replace if needed. Replace your foam with the polystyrene sheet foam from HD or Lowes.

This sealer is recommended for curing aluminum boats thanks to its waterproof property. It provides a perfect bond of plastic or rubber to aluminum surfaces. The sealant comes in a convenient cartridge making it easier to apply it without a caulking gun.

It had blue silicon sealant on it from a prior owner so I peeled that all off and used a wire brush on a drill to cleanrough up the outside and sprayed several coats on it. I was worried my bilge pump had gone out last year when I turned it on and no water pumped out. How to Leak Proof an Aluminum Boat - YouTube.

How to Leak Proof an Aluminum Boat. If playback doesnt begin shortly try. Best way to reseal a rivited aluminum boat 1.

Do a leak test on your boat fill the bottom of the boat with a few inches of water while its on the trailer and watch the outside of the bottom for leaks. Mark the leaks when you find them. My buddies boat is a twelve foot aluminum flat bottom but v shaped prow.

The thing leaks all over the place you cant really pinpoint leaky seams or rivets. Does anyone know how I could go about just sealing the entire interior of the boat. I was going to redo all the seats and decks so I wou.

Locate the leaking rivets. Prop the boat up and spray water inside to locate the loose rivets. Dry thoroughly and sand the area around the rivets with 120 grit to remove any paint and provide some tooth for the epoxy.

Etch the area with WEST 860 Aluminum Etch Kit. Mix and apply a layer of GFlex epoxy. Wetlander is a perfect example.

Wetlander boat coatings have excellent adhesion to both aluminum and to the sealant itself. Coating Wetlander over your seals and over your floor andor hull bottom will create a double-protected waterproof seal on your leaking boat without having to weld it shut. This makes a huge difference.

Apr 19 2016 - There are multiple methods to repair leaking rivets on an aluminum jon boat. Some are mechanical involving resetting the rivets. Some are chemical using a sealant around the rivets.

All the methods have one thing in common. Before you begin the repair you fill the boat with water to find the leaks. Aluminum boats are corrosion resistant but they are not corrosion proof.

So as long as you have an aluminum boat corrosion will likely be a concern. However do not despair. As a boat owner you can take several steps to protect your aluminum boat from the effects of electrolysis and corrosion.

As someone else pointed out this is probably a better question for boat builders. That being said a riveted aluminum patch would last just fine if done correctly. Aircraft get patched up that way all the time and they have to flex and be pressurized and go through a lot of torment that is at least equal to a boat hull.

Mix the hardener and resin of an epoxy sealing compound such as West Systems GFlex 650 according to the compounds directions. Heat the seamed area and rivets with a propane torch to dry the seam. Apply the epoxy compound to the seam by painting the compound onto the seam with a plastic paint scraper or by injecting the epoxy into the seam with a specialized syringe.

The surface must be clean dry and free of dirt dust grease loose paint oils or other contaminants. Sand aluminum with 80-grit sandpaper within a 1 radius of the leak or repair until the metal is shiny. Remove any sanding residue before application.

For best results use Aluminum Boat Etch Wash. How do I apply Aluminum Boat Epoxy Leak Sealer. Discussion Starter 1 Feb 24 2012.

I have a 12ft v-hull aluminum row boat. It only gets useda couple weeks a year but it is very leaky and takes on about 5 gallons of water per hour. It leaks on the seams where the rivets connect the ribs to the inside of the boat.

Ive tried brazing the seams but that didnt work out very well since.